Elastic-Plastic Seismic Analysis of Concrete-Filled Steel Tube Composite Column Bridge Piers
Literature Overview and Core Contribution
This paper by Zeng Yan, Pan Liyun and Zhao Shunbo from the School of Civil Engineering and Transportation at North China University of Water Resources and Electric Power addresses a question that has become increasingly important in bridge engineering: can a concrete-filled steel tube (CFST) composite column pier replace a conventional reinforced concrete pier in a region where the water flow is restricted and the pier size must be minimised? The authors use the finite element program Midas/Civil to perform an elastic-plastic analysis of a CFST composite column pier under two levels of seismic loading, designated E1 and E2 in the Chinese seismic design code for bridges. The E1 level corresponds to a frequent earthquake, where the structure is expected to remain elastic, and the E2 level corresponds to a rare earthquake, where the structure is expected to develop plastic hinges but not collapse. The authors compare the performance of the CFST composite column pier with that of a reinforced concrete pier that was not feasible because its larger cross-section would have exceeded the allowable water blockage ratio. The results show that the CFST composite column pier has superior load-carrying capacity and ductility compared to the reinforced concrete pier, and the authors conclude that the CFST composite column concept is a viable alternative for bridges in flood-prone areas where the pier size is constrained by hydraulic requirements.
Technical Points and Seismic Performance Interpretation
The key technical point in this paper is the definition of the CFST composite column, which is different from a conventional CFST column. In a composite column, the steel tube is placed at the centre of the section, and it is surrounded by a layer of reinforced concrete. This arrangement has several advantages over a conventional CFST column. First, the outer reinforced concrete layer provides fire protection for the steel tube, which is a critical consideration for bridge piers that may be exposed to vehicle fires. Second, the outer concrete layer increases the stiffness of the section, which reduces the lateral deflection under seismic loading. Third, the steel tube at the centre provides a high level of confinement for the inner concrete core, which enhances the ductility of the section. The elastic-plastic analysis in the paper uses a fibre model, where the section is divided into a number of fibres, each with its own stress-strain relationship. The steel tube is modelled with an elastic-perfectly plastic stress-strain curve, and the concrete is modelled with a confined concrete stress-strain curve that accounts for the confinement provided by the steel tube and the outer reinforcement. The analysis is performed for both the E1 and E2 seismic levels, and the results are presented in terms of the displacement ductility ratio, the curvature ductility ratio, and the plastic hinge length. The comparison with the reinforced concrete pier shows that the CFST composite column pier achieves a higher displacement ductility ratio, which means it can undergo larger inelastic deformations before failure. This is a critical advantage in a rare earthquake, where the structure must dissipate a significant amount of energy through plastic deformation.
Engineering Practice and Site Considerations
From a construction standpoint, the CFST composite column pier is more complex to build than a conventional reinforced concrete pier, because it requires the placement of a steel tube at the centre of the section, followed by the placement of the inner concrete core, and then the placement of the outer reinforced concrete layer. The sequence must be carefully planned to avoid voids in the inner concrete core, which is difficult to inspect after the outer layer is cast. I have seen a project where the inner concrete core of a CFST composite column was not fully compacted, and the void was only discovered when the pier was subjected to a lateral load test. The void reduced the load-carrying capacity by about 15 percent, which was enough to fail the acceptance criteria. The solution is to use a self-compacting concrete mix for the inner core, and to place it through a tremie pipe that is withdrawn slowly as the concrete rises. The outer reinforced concrete layer can be cast using conventional methods, but the formwork must be designed to resist the lateral pressure from the fresh concrete, which is higher than for a conventional column because the outer layer is relatively thin and the formwork is tall. In a bridge pier that is 15 metres high, the lateral pressure at the bottom of the formwork can reach 60 kilopascals, which requires robust formwork ties and a stiff formwork panel system. I have seen formwork failures in tall piers, and they are always expensive and dangerous.
Key Questions and Reflections
The paper raises a question that I have often discussed with bridge designers: what is the optimum ratio of the steel tube diameter to the overall column diameter? The authors do not address this directly, but from my experience, a ratio of 0.4 to 0.5 gives a good balance between the confinement effect and the stiffness contribution. If the tube is too small, it does not provide enough confinement to the inner core, and the ductility improvement is marginal. If the tube is too large, the outer concrete layer becomes too thin, and it is prone to spalling under seismic loading. Another question is the effect of the steel tube on the corrosion resistance of the pier. In a marine environment, the outer concrete layer protects the steel tube from chloride ingress, but if the outer layer cracks, the chloride can reach the steel tube and cause corrosion. The corrosion products expand and can cause the outer layer to spall, which accelerates the corrosion. I have seen this in a bridge in a coastal area where the outer concrete layer cracked due to a combination of shrinkage and cyclic loading, and the steel tube showed significant corrosion after five years of service. The solution is to use a high-performance concrete mix for the outer layer, with a low water-to-cement ratio and a high content of supplementary cementitious materials, and to apply a corrosion inhibitor to the steel tube before it is placed. The paper does not address this issue, but it is a critical consideration for the long-term durability of the pier.
Study Insights and Practical Recommendations
The most valuable takeaway from this paper is the confirmation that the CFST composite column pier can achieve a higher level of ductility than a conventional reinforced concrete pier, which is exactly what is needed in a rare earthquake. For my own practice, I would use the results of this paper as a basis for a preliminary design, but I would always verify the design with a time-history analysis that uses actual earthquake records, because the response spectrum method used in the paper is a simplification that may not capture the full range of inelastic behaviour. I would also specify a minimum concrete cover of 50 millimetres for the outer layer, and I would require the use of a self-compacting concrete mix for the inner core to ensure that the core is fully compacted. On the construction side, I would require a trial pour for the inner core to verify the concrete mix and the placement procedure, and I would require ultrasonic testing of the inner core to detect any voids before the outer layer is cast. The cost of the ultrasonic testing is small compared to the cost of a void that is discovered after the outer layer is cast, which would require the demolition of the pier. In delivery, the steel tube should be delivered with a protective coating on the outside, and the end caps should be welded on to prevent water ingress during storage. I have seen steel tubes that were delivered without end caps, and rainwater accumulated inside, which caused corrosion on the inner surface. The corrosion was not visible until the tube was cut, and by then the damage was done.
Conclusion and Outlook
This paper makes a valuable contribution to the seismic design of bridge piers in flood-prone areas, and it provides a strong argument for the use of CFST composite columns as an alternative to conventional reinforced concrete piers. The main limitation is the use of a response spectrum analysis, which does not fully capture the inelastic behaviour of the structure under a rare earthquake. For the industry, the next step should be a comprehensive experimental programme that includes shaking table tests on scaled models of CFST composite column piers, so that the numerical results can be validated with physical evidence. I would also like to see guidance on the design of the connection between the pier and the pile cap, because this is a critical detail that is often overlooked. In my experience, the connection should be designed as a full moment connection, with the steel tube anchored into the pile cap using headed studs or a steel base plate. The paper is a good starting point, but it should be read alongside the relevant sections of the Chinese seismic design code for bridges and the Eurocode 8 provisions for composite structures, which give more detailed rules for the design of composite columns under seismic loading. In the end, the design of a CFST composite column pier is a balance between structural performance and construction complexity, and this paper shows that the balance can be struck in favour of performance without compromising safety.
Zhuojin Pipe Fitting Co., Ltd