ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Heat Treatment Process for 1Cr5Mo Alloy Seamless Steel Pipe

Literature Overview and Metallurgical Context

This paper by Li Lianjin and Zong Weibing is a compact but valuable study on the heat treatment of 1Cr5Mo alloy seamless steel pipe. 1Cr5Mo is a chromium-molybdenum steel with roughly 4–6% Cr and 0.4–0.6% Mo, used extensively in petroleum refining for furnace coils, transfer lines, and other components that must resist high-temperature hydrogen attack and sulfidation. It is essentially the Chinese equivalent of ASTM A335 P5 or ASTM A200 T5, and it is a material I have specified and shipped for many refinery projects. The paper addresses a real production problem: how to get consistent mechanical properties and a fine-grained microstructure in a pipe that has been hot-rolled and then air-cooled. The as-rolled structure is often bainitic or even martensitic, with high hardness and low toughness, so a proper normalizing and tempering cycle is essential.

The authors used an optimization test method, varying the normalizing temperature, the tempering temperature, and the holding times. They concluded that the optimal process is: normalizing at 920–960°C for 60 minutes, followed by tempering at 720–780°C for 60 minutes. The resulting mechanical properties were excellent: ultimate tensile strength 615 MPa, yield strength 505 MPa, elongation 23%, impact energy 280 J, and hardness ≤180 HB. The grain size was 8.5 on the ASTM scale, which is fine and desirable. These values comfortably meet the typical requirements for P5 pipe, which usually specify a tensile strength of 415–585 MPa and a yield strength of at least 205 MPa. The paper's results are actually stronger than the standard minimum, which is a good sign that the process is robust.

Core Technical Points and Process Window Analysis

The key metallurgical principles here are straightforward but often ignored in production. 1Cr5Mo is a hardenable steel, so the cooling rate after hot rolling determines the as-rolled microstructure. If the pipe is air-cooled from a high temperature, it will transform to bainite or martensite, which is hard and brittle. Normalizing re-austenitizes the steel and then air-cools it, producing a fine ferrite-pearlite or ferrite-bainite structure. The normalizing temperature must be high enough to dissolve all the carbides and homogenize the chromium and molybdenum in the austenite, but not so high that the austenite grain grows excessively. The paper's range of 920–960°C is sensible. I have seen mills run P5 at 950°C with good results, but I have also seen grain coarsening at 1000°C.

Tempering is the critical step for toughness and stress relief. The tempering temperature of 720–780°C is in the upper range for this steel, which promotes the formation of stable chromium carbides and the recovery of the dislocation structure. The 60-minute hold is adequate for a pipe wall thickness of up to about 20 mm. For thicker walls, I would extend the hold time by roughly 1 minute per millimeter of wall thickness beyond 20 mm. The paper does not mention this, but it is a practical rule I apply in the mill.

Process Parameter Paper's Optimal Range My Practical Range Notes
Normalizing temperature 920 – 960°C 930 – 950°C Keep below 970°C to avoid grain growth.
Normalizing hold time 60 min 45 – 90 min Scale with wall thickness; 60 min for ≤20 mm wall.
Tempering temperature 720 – 780°C 730 – 760°C Upper end gives better toughness, lower hardness.
Tempering hold time 60 min 60 – 120 min Longer hold reduces residual stress.
Cooling after tempering Air cool Air cool Do not quench; air cooling is essential.

The paper reports a hardness of ≤180 HB, which is a good target. In practice, I have seen P5 pipe come out at 200–220 HB if the tempering temperature is too low or the hold time too short. That hardness is acceptable for some applications but can cause problems in welding, especially for the heat-affected zone. The impact energy of 280 J is impressive for this steel grade. I would normally expect 150–200 J for a well-tempered P5. The high value suggests a very clean steel with low sulfur and phosphorus, which is a credit to the steelmaking practice at Tianjin Pipe.

Engineering Practice Cases and Production Lessons

I have run P5 pipe through a rotary hearth furnace and a piercing mill, and I can tell you that the heat treatment is where you win or lose the order. One issue that the paper does not address is the effect of the pipe's final wall thickness on the heat treatment response. A 6 mm wall pipe will respond differently from a 30 mm wall pipe. The thinner pipe will cool faster after normalizing, giving a harder and stronger as-normalized structure, which then requires a higher tempering temperature to bring the hardness down. The thicker pipe will cool slower, giving a softer structure, and may not reach the desired strength unless the normalizing temperature is raised. The paper's optimized process was likely developed for a specific wall thickness, probably around 10–15 mm. I would always recommend running a trial heat with the actual production wall thickness before committing to a full batch.

Another practical lesson concerns the tempering furnace atmosphere. 1Cr5Mo is sensitive to decarburization and oxidation at high temperatures. If the furnace has a poor atmosphere, the pipe surface can lose carbon, which reduces the surface hardness and can lead to a soft skin that is prone to wear or corrosion. I have seen this on a batch of P5 pipe that was tempered in an old furnace with a leaking burner. The pipe looked fine on the outside, but the surface hardness was 20 HB lower than the core. We had to grind off the decarburized layer, which was a costly mistake. The paper does not discuss furnace atmosphere, but I would insist on a slightly reducing atmosphere or a nitrogen purge during tempering.

The grain size of 8.5 is excellent. To achieve this consistently, the steel must be microalloyed with a grain-refining element such as aluminum or niobium. The paper does not mention the steel chemistry, but I would expect a fine aluminum addition of 0.02–0.04% to be present. Without it, the grain size would be 5–6, and the toughness would be significantly lower. If you are specifying P5 pipe for a critical service, always ask the mill for the grain size and the aluminum content.

Reflections and Recommendations for the Mill

This paper is a good example of a practical optimization study. It does not break new ground in metallurgy, but it provides a reliable process window that a mill can adopt. My main reflection is that the paper's results are specific to the steelmaking route and the pipe size used in the trial. A different mill with a different continuous caster or a different piercing mill might need slightly different parameters. The best approach is to use the paper's values as a starting point and then run a design of experiments on your own equipment.

For fellow engineers, I would emphasize three things. First, always verify the mechanical properties on the actual production pipe, not just on a coupon from the trial. The heat treatment furnace has temperature gradients, and the pipe at the ends of the charge will be different from the pipe in the middle. Second, do not skip the impact test. The paper reports 280 J, but I have seen P5 pipe pass the tensile test and fail the impact test because the tempering temperature was too low. Third, if you are welding this pipe, remember that the heat-affected zone will be hard and susceptible to hydrogen-induced cracking. You must preheat to at least 200°C and use a low-hydrogen electrode. The heat treatment of the pipe is only half the battle; the welding procedure is the other half.

The paper is a solid reference for anyone producing or using 1Cr5Mo seamless pipe. It is short but practical, and the optimized parameters are credible. I would keep a copy in the mill's quality control office and use it as the basis for the standard heat treatment procedure.